Post by naigon on Feb 9, 2015 12:18:27 GMT -5
Petite in size, immense in impact
The next step in sound board evolution is here; after many successful releases with the Igniter™ and Igniter Mini™ platforms spanning five releases, it is time to unveil the next iteration in the Igniter™ line:
Introducing Igniter 2™
Igniter 2™ has been built from the ground up, taking all the learnings of the past Igniter™ boards and rolling it up into one package that will rock the saber world. There were many hardware and firmware upgrades to make this release possible. Below I summarize the changes, and each day after today I will release a video for each of the changes to go over it in more details.
As seen from the picture, the hardware has been completely redesigned. The following changes have been made:
- Integrated MaxAmp(TM) - now the loud and clear 2.4w amp is available without a separate board
- 6 degrees of freedom - the board is equipped with a 3-axis gyro and 3-axis accelerometer. Say bye-bye to the off-board clash sensor, and hello to better motion.
- Spring-loaded push-push type micro SD card locks card into place, no more tugging on card to remove it.
- Easy-soldering pads for main features, medium pads for more advanced features (still on edge of board). No more soldering mid board or to random components.
- Even smaller size: 2.07" (L) x 0.85" (W) x 0.23" (H) with TruDrive™ attached, 1.75" (L) with TruDrive™ removed.
Above is a picture of all three generations of Igniter™ side-by-side. You can see the obvious length differences. The second picture is Igniter Mini™ next to Igniter 2™. Here you can see the 0.93" width vs. the 0.85" width... in practice this makes a big difference (Igniter 2™ fits inside the Duke with no mods).
With the new sensor, the following improvements are apparent:
- SaberSense™ - perfect motion tracking for every swing.
- Clashes without limitations - no external sensor and clashes have sensitivity adjustments.
- Swing/Slash definition improved; completely natural to trigger one vs. the other.
Motion is too good to just explain, you need to see it to understand...
Some improvements were made to the basic firmware. These improvements are:
- Classic Aux button hold functionality from R4 previous restored, while holding aux and twisting still performs MultiPhase™
- Low power mode to turn off accents/motion when in idle (helps to conserve power at cons).
- ActionStart - perform the DualPhaseTM motion to start the saber from idle.
- Saber Cinema™ improvement - /tracks folder is now on the root, so all tracks are accessible from each font. TrackStart (trckStrt) Config Editor parameter allows the starting font to be set for each font, allowing some configuration per font.
- Config value to swap buttons, allowing configurability between main and aux button on a control box.
If all of the above wasn't enough, Naigon's Electronic Creations is pleased to be the first company to bring you Saber AppsTM. Saber AppsTM is the first mini OS that is able to load many different applications on one saber. From configuration to utilities to even games, Saber AppsTM allows an infinite amount of experiences possible in the saber.
Currently there are 6 apps; ColorEditor, MotionEditor, Saber Says™, Spark Color™, Spark Colorset Editor, and Igniter™. Yes that is right; you can use both Spark Color™ and Igniter™ on the same board!
Saber Says™ is also a great experience, as it is the world's first game on a saber. Challenge your friends or beat your own high score in this saber-ized spin on the classic MB memory game.
And if all that wasn't enough, now new apps and firmware updates can be loaded by simply switching out the micro SD card; no send ins required (unless of course the loading app changes, then a send in would be required).
All the videos are now up in their respective sections. Check back to IRA for a few more completed sabers with Igniter 2™ installed to see it in action some more.
When will it be ready?
Expect my site to be updated within a week. Be patient as I still need to finish bundling up the Config Editor and am waiting for new micro SD cards to come in.
This is too awesome, what's the catch!?
The only downside to the new board is that the cost of manufacture is slightly more, so the price has increased slightly as well (TBD, ~ 10 bucks more). However with all the improvements the extra cost is worth it. In the future I may offer package discounts when buying multiple things, but I need to figure out the best way to update my site to do that first.
Godspeed, and MTFBWY.